Beaver Appliance

Maytag washer repair, top-load and front-load.

Maytag A brand we repair

Beaver Appliance repairs Maytag top-load and front-load washers in South Florida and Tampa Bay, as an independent company not affiliated with Maytag. A $69 diagnostic visit finds the fault, credited to the repair; the price is in writing before any work.

Call or text and we’ll give you the earliest time we have.

Diagnostic visit
$69, credited to the repair
Price
In writing, before any work
Work done
Only what you approve
Google rating, South Florida
5.0 from 14 reviews
A white top-load washer with its lid up and the wash basket open
The top of a white top-load washer with its lid raised and the wash basket open, in a bright laundry room

Washing machines and more, in customers’ words

Our South Florida Google profile: rated 5.0 from 14 Beaver Appliance reviews.

  • Washing machine

    “Aizat was very prompt and did a wonderful job fixing my washing machine. …”

    ★★★★★ Debbie B. Jul 2026, Google review
  • Refrigerator

    “… The technician took the time to diagnose the problem properly and had everything back up and running. …”

    ★★★★★ Joey C. Sep 2026, Google review

What is your Maytag washer doing?

Showing a code? Start with the code table.

Won’t fill, or fills slowly

First check: hot and cold both on and connected. Maytag says the washer “will not properly operate with only one incoming source of water”.

Call us if it still fills slowly.

Water still in the tub

First check: the drain hose, untaped and not pushed too deep. Unplug a front-loader before opening its pump filter, if it has one, with a large container and a towel under it; after a hot cycle, let the water cool.

Call us if water is still there after Drain & Spin.

Won’t spin, clothes soaking wet

First check: Maytag says a top-loader paused late in the cycle, or cut off by a power failure mid-spin, may not reach full speed.

Call us if an even load stays wet after Drain & Spin.

Water on the floor

First check: with the valves shut, a hose washer at both ends of each fill hose, connections tight but not over-tightened. Maytag says fill hoses should be replaced every five years.

Call us if it still leaks, and shut the valves between loads.

Shakes, walks or bangs

First check: a top-loader filled only to the top row of holes, never one rug alone; a new front-loader’s four shipping bolts out and jam nuts tight.

Call us if it shakes when level and evenly loaded.

Lid lock light flashing

First check: Maytag says “clothing, lint, and detergent build-up can prevent the lid from locking”, so wipe the lock area. A start-up click and slight basket turn are its self-test.

Call us if it still flashes after the five-minute power cycle.

Maytag washer codes

Photograph the display and the model label, then try Maytag’s five-minute power cycle once.

Maytag likens it to restarting a computer: unplug the washer, or turn off its breaker, for five minutes. Code back? Text us both photos. Some codes differ between top-loaders and front-loaders.

Code What Maytag says it means First check, then
F8 E1 LF F20 FH Lo FL

Low water flow in, or slow to fill

Both valves open, both hoses on, unkinked.

F9 E1 F21 drn Ld F0 E8

Long drain, or water left in the tub

Hose untaped, not too deep; then Drain & Spin.

F5 E2 F5 E3 F22 LdL dL

Lid or door not locking

Clear the lock area. LdL again: service.

F5 E4 dr

Top-load: lid open. Front-load: three cycles run without opening the door Differs by type

Open and close the lid or door, then restart.

dU LdU

Lid can’t unlock: something sits on it No service needed

Lift the basket off.

F0 E5 F0 E9 OFb uL

Off balance

Spread the load; pair a rug with towels.

F0 E3 oL

Top-load: overload. Front-load: none given Differs by type

Take some items out.

Sud Sd 5d F0 E2

Excess suds; it runs a suds reduction routine No service needed

Let it finish. HE detergent; hose unkinked.

F8 E3

Front-load: overflow from too much water or foam. Top-load: none given Differs by type

Measured HE detergent, less in soft water.

F0 E4 HC

Water too hot, or hoses on the wrong inlets

Valves off, then swap reversed hoses back.

F3 E2

Top-load: hot and cold hoses may be reversed. Front-load: none given Differs by type

Valves off, swap them, then open both valves.

F7 E1

Front-load: the motor can’t reach the cycle’s speed. Top-load: none given Differs by type

New front-loader: four shipping bolts out.

F8 E6

Top-load: lid opened during a soak, or no hot water detected Depends on the model

Shut the lid; open the hot valve.

F2 E3 F2 E4 F2 E5 F6 E2 F6 E3 F7 E2 F7 E7 F7 E9 F3 E1

Top-load: control, user interface or wiring; F3 E1, water level not sensed

Power cycle once, then text us.

PF

A power failure interrupted the cycle

Hold Start to restart.

rL F0 E1 F0 E7 F-34

Items in the drum during Clean Washer

Take them out, restart.

CL LoC LC Int Fd Lid

A setting or a reminder Not a fault

CL: Clean Washer is due. LoC: hold Control Lock three seconds.

Where Maytag puts the model label

Top-loader: “beneath the washer lid on the tub rim”. Front-loader: “inside the washer door, on the rim of the opening”.

Text a photo to (813) 513-1699

How a Maytag washer visit works

  1. Tell us what it’s doing

    Call or text us. The appliance, the symptom and any code are enough to start.

  2. We find the fault

    For the $69 diagnostic visit, credited to the repair if you go ahead.

  3. Get the price in writing

    Before any work starts. No repair until you say yes.

  4. We fix it

    Only the work you approved, at the price you approved.

  5. Get the paperwork

    The appliance, the work done and the date, in writing.

Maytag washer questions

Didn’t see yours? Call (813) 513-1699 Text the code

What does F8 E1 mean on a Maytag washer?

Maytag says the washer “is not detecting the correct amount of incoming water”: a fill problem, not a drain fault. Open both valves fully and check both hoses; Maytag adds that anti-flood devices can cut the flow.

Why won’t my Maytag front-load washer door open?

With the Add a Garment light off, press Pause/Cancel twice; Maytag says the door can take up to five minutes to unlock. After an F8 E1 code, press Power and wait out a drain of about 8 to 10 minutes. Still locked? Call or text us.

How do I reset a Maytag washer?

Maytag’s reset is a power cycle: five minutes unplugged, or with the breaker off if it’s hard-wired. Try it once. If the code persists, Maytag says a technician should diagnose the washer.

Is my Maytag washer still under warranty?

Maytag’s limited warranty typically runs one year from the date of purchase, parts and labor, with proof of that date; in that year the repair goes through Maytag. It doesn’t pay to fix household plumbing, inlet hoses included. Once the warranty has run out, you choose who repairs it.

More on Maytag and washers

Where we work

Beaver Appliance repairs Maytag washers across South Florida: Broward County and nearby parts of Miami-Dade and Palm Beach counties. Call or text (754) 285-8880.

Beaver Appliance repairs Maytag washers across Tampa Bay: Pasco and Hillsborough counties and nearby parts of Pinellas and Hernando counties. Call or text (813) 513-1699.