Beaver Appliance

Whirlpool washer repair, top-load and front-load.

Whirlpool A brand we repair

Beaver Appliance repairs Whirlpool top-load and front-load washers in South Florida and Tampa Bay, as an independent company not affiliated with Whirlpool. A $69 diagnostic visit finds the fault, credited to the repair; the price is in writing before any work.

Call or text and we’ll give you the earliest time we have.

Diagnostic visit
$69, credited to the repair
Price
In writing, before any work
Work done
Only what you approve
Google rating, South Florida
5.0 from 14 reviews
A technician’s hand on an open tool bag beside a white front-load washer
A technician in a navy polo kneeling at a white front-load washer with its door open, one hand on an open tool bag

Whirlpool and more, in customers’ words

Our South Florida Google profile: rated 5.0 from 14 Beaver Appliance reviews.

  • Washing machine

    “Aizat was very prompt and did a wonderful job fixing my washing machine. …”

    ★★★★★ Debbie B. Jul 2026, Google review
  • Older Whirlpool refrigerator

    “… He analyzed the cooling problem on my older model Whirlpool refrigerator. He communicated the issues and answered all my questions. …”

    ★★★★★ Christine F. Aug 2026, Google review

What is your Whirlpool washer doing?

Showing a code? Start with the code table.

Won’t fill, or fills slowly

First check: both valves fully open, hoses unkinked and hot to hot. Whirlpool says flood safety devices “can interfere with the appliance’s performance”.

Call us if it still won’t fill.

Water left in the tub

First check: the drain hose, unkinked, untaped and not too far down the drainpipe. Then a front-loader’s pump filter, on models with one: unplug the washer and set a large container and a towel under it, as Whirlpool says, since the tub’s water drains out there. After a hot cycle, let it cool first.

Call us if water stands after Drain & Spin.

Clothes still soaking wet

First check: Low Spin, No Spin and gentle cycles leave clothes wetter, and a cycle keeps its last settings.

Call us if Drain & Spin on an even load leaves them wet.

Water on the floor

First check: with both valves shut, a rubber washer in each hose end and every connection tight; nothing under a front-loader’s door seal. Packets never go in the drawer, Whirlpool says.

Call us if it leaks with the hoses tight.

Shakes, bangs or grinds

First check: a new front-loader’s four shipping bolts out, all four feet firm. Over a drain pan, Whirlpool says “the tub bottom may be rubbing against the drain pan”: raise the legs.

Call us if it shakes once level.

Lid lock flashing, or a locked door

First check: wipe lint and detergent off the lid lock and striker. A front-loader holding water opens after Drain & Spin.

Call us if the five-minute reset doesn’t free it.

Whirlpool washer codes

Photograph the code and the model label, then give it Whirlpool’s five-minute reset, once.

Unplug it, or switch its breaker off, for five minutes. Back again? Text us both photos: some codes mean one thing on a top-loader, another on a front-loader.

Code What Whirlpool says it means First check, then
F8 E1 LF F20 FH Lo FL

Not enough water coming in, or slow to fill

Valves fully open, hoses unkinked, hot to hot.

F9 E1 F21 drn Ld F0 E8

Slow to drain, or water left in the tub

Hose unkinked and untaped; a front-loader’s pump filter, unplugged, a container under it; then Drain & Spin.

F5 E2 F5 E3 F22 LdL dL

The lid or door won’t lock

Clear clothing and build-up from the lock. LdL twice: service.

F5 E4 dr

Top-load: lid open. Front-load: three cycles in a row with the door shut Differs by type

Close the lid, or open and shut the door.

dU LdU

Something on the lid stops it unlocking No service needed

Lift it off.

F0 E5 F0 E9 OFb

Off balance

Spread the load, then Drain & Spin.

F0 E3 oL

Top-load: too heavy a load. Front-load: none published Differs by type

Take items out.

Sud Sd 5d F0 E2

Too many suds; a suds routine runs No service needed

Let it finish; measured HE detergent.

F8 E3

Front-load: overflow, too much water or foam. Top-load: none published Differs by type

Less detergent, then Clean Washer.

F0 E4 HC

Water too hot, or hot and cold hoses swapped

Valves off, then swap the hoses back if reversed.

F3 E2

Top-load: hoses may be reversed. Front-load: none published Differs by type

Valves off, then swap them back.

F7 E1

Front-load: motor speed sensing error. Top-load: none published Differs by type

New front-loader: all four shipping bolts out.

F8 E6

Top-load: lid open during a soak, or no hot water Depends on the model

Close the lid; hot valve open.

F2 E3 F2 E4 F2 E5 F6 E2 F6 E3 F7 E2 F7 E7 F7 E9 F3 E1

Top-load: control, user interface or wiring; F3 E1, water level not detected

The reset once; back again, text us.

PF

Power failed mid-cycle

Press Start, or cancel and restart.

rL F0 E1 F0 E7 F-34

Clothes in the drum during Clean Washer

Empty it, restart.

CL LoC LC Int Fd Lid

A reminder or a setting Not a fault

CL: Clean Washer is due. LoC: Control Lock on. Int: paused; draining can take 20 to 30 minutes.

Text us the code and the label

Whirlpool puts it under the lid on the tub rim, or on the rim of the door opening.

Text a photo to (813) 513-1699

What a Whirlpool washer visit involves

  1. Tell us what it’s doing

    Call or text us. The appliance, the symptom and any code are enough to start.

  2. We find the fault

    For the $69 diagnostic visit, credited to the repair if you go ahead.

  3. Get the price in writing

    Before any work starts. No repair until you say yes.

  4. We fix it

    Only the work you approved, at the price you approved.

  5. Get the paperwork

    The appliance, the work done and the date, in writing.

Whirlpool washer questions

Didn’t see yours? Call (813) 513-1699 Text the code

Why is the lid lock light flashing on my Whirlpool washer?

Whirlpool says the lid hasn’t locked: it isn’t closed, the lock or striker is blocked, or the lock motor has no power. Hold Start up to three seconds, wipe the lock area, then try the five-minute reset. Still flashing? Whirlpool says call a technician.

What does F5 E4 mean on a Whirlpool washer?

On a Whirlpool front-loader, three cycles have run with the door shut: open and close it, then restart. On a top-loader, the lid is open; if closing it doesn’t clear the code, it needs service.

How do I reset a Whirlpool washer?

Unplug the washer for five minutes, or switch off its breaker if it’s hard-wired; Whirlpool says that can clear temporary glitches. Do it once. If the code returns, text us a photo of it and the model label.

Is my Whirlpool washer still under warranty?

Whirlpool’s standard warranty covers parts and labor for one year from delivery, with proof of purchase, and in that year Whirlpool arranges the repair. Running a front-loader with its shipping bolts in can void it, Whirlpool says. After the first year, the repairer is your choice.

More on Whirlpool and washers

Where we work

Beaver Appliance repairs Whirlpool washers across South Florida: Broward County and nearby parts of Miami-Dade and Palm Beach counties. Call or text (754) 285-8880.

Beaver Appliance repairs Whirlpool washers across Tampa Bay: Pasco and Hillsborough counties and nearby parts of Pinellas and Hernando counties. Call or text (813) 513-1699.