Beaver Appliance

Whirlpool dishwasher repair, codes and blinking lights.

Whirlpool A brand we repair

Beaver Appliance repairs Whirlpool dishwashers in homes across South Florida and Tampa Bay, as an independent company not affiliated with Whirlpool. A $69 diagnostic visit finds the fault, credited to the repair; the price is in writing before any work.

Call or text and we’ll give you the earliest time we have.

Diagnostic visit
$69, credited to the repair
Price
In writing, before any work
Work done
Only what you approve
Google rating, South Florida
5.0 from 14 reviews
An open dishwasher, its lower rack rolled out onto the door
A built-in stainless dishwasher under a white countertop, door down and lower rack rolled out, seen from the side

Whirlpool and other repairs, in customers’ words

Our South Florida Google profile: rated 5.0 from 14 Beaver Appliance reviews.

  • Older Whirlpool refrigerator

    “… He analyzed the cooling problem on my older model Whirlpool refrigerator. He communicated the issues and answered all my questions. …”

    ★★★★★ Christine F. Aug 2026, Google review
  • Appliance repair

    “… He diagnosed the problem quickly, explained what needed to be done, and got the job done right. …”

    ★★★★★ Arlene J. Aug 2026, Google review

What is your Whirlpool dishwasher doing?

Showing a code? See the code table.

Water left in the tub

First check: water halfway up the filter area is normal; it keeps the seals moist, Whirlpool says. More? Breaker off, towels down, bail it into a bucket. Then rinse the filters; unkink the drain hose.

Call us if water still stands.

Water on the floor

First check: a spot under the door vent is condensed steam, Whirlpool says. Dish soap suds push water out: use dishwasher detergent only. Still dripping? Breaker off, water shut under the sink, towels at the door.

Call us if it leaks from underneath.

Away for the summer months? Whirlpool says to turn off its water and power supply.

Won’t start, or no lights

First check: the water valve under the sink fully open; Whirlpool says a closed one stops a start. Then the breaker, Control Lock, Delay Wash and the door latch: push until it clicks.

Call us if the reset doesn’t revive it.

Dishes come out dirty

First check: the valve fully open (a flood-stop device fitted wrong blocks water, Whirlpool says), 120°F at the tap, and the middle spray arm turning freely by hand.

Call us if food stays on with the arm free.

Dishes still wet

First check: rinse aid (a full dispenser lasts one to three months, Whirlpool says), heated dry, plastics off the bottom rack. Then Whirlpool’s heater test: a Sanitize cycle with hot tap water, the door shut.

Call us if the Sanitize light blinks instead of staying on. Whirlpool says “service will need to be scheduled.”

Grinding, buzzing or thumping

First check: a drain pump hum, a valve hiss, a fan after the cycle and, on some models, a chopper’s grind are normal, Whirlpool says. Buzzing or new grinding: clear the filter area. Thumping: something past a rack hits a wash arm.

Call us if it stays with the filter clear.

Whirlpool dishwasher codes and lights

Photograph the code and the model label first; then give Whirlpool’s reset one try, except F8 E4 and F8 E5: follow their rows first.

Codes vary by model, Whirlpool says; for most below, one that returns after the reset means service.

Code What Whirlpool says it means First check, then
Clean light blinking

A code, sent in flashes

Count the flashes (questions below). Steady after a cycle: normal.

F9 E1

Long drain: it isn’t draining

Breaker off, towels down; filters, drain hose, disposer. Then the reset.

F9 E2

Drain motor error

Hose straight, disposer clear, a new one’s knockout plug out; the reset.

H2O F8 E1

Not detecting water

Water valve on, supply hose unkinked, then Start.

F8 E4

Water in the drip tray, says Whirlpool’s help site; an overfill, says its manual

Shut the water off under the sink if you can, press Cancel once, keep the door closed, and call us; a photo of the model label helps.

F8 E5

Fill valve stuck open

Water off under the sink if you can, Cancel once, and keep the door shut. A visit.

F6 E3

Excessive suds

Scoop them out with a plastic cup; a full cycle, empty, no detergent.

F6 E4

Water float switch

Whirlpool says an unlevel dishwasher can trip it; the reset.

F7 E2

Wash motor error

The reset; back again, a visit.

F6 E1

User interface error, main control

The reset; if it stays, a visit.

F4 E2 F4 E3

Heating system (F4 E2), heating error (F4 E3)

The reset; back again, a visit.

F2 E2 F2 E1

Main control communication error (F2 E2), stuck key or console (F2 E1)

The reset; back again, a visit.

F3 E2

Thermistor or OWI sensor

The reset; back again, a visit.

FA E4 F10 E4

Diverter valve error

The reset; back again, text us.

F8 E2

Fill valve electric error

The reset; back again, a visit.

Sanitize light blinking

The sanitizing temperature wasn’t reached

Hot tap, door shut. Blinking after a full Sanitize cycle: a visit.

Photograph both, send one text

Whirlpool puts the label on the tub frame’s left side, inside the door.

Text a photo to (813) 513-1699

Your Whirlpool dishwasher visit

  1. Tell us what it’s doing

    Call or text us. The appliance, the symptom and any code are enough to start.

  2. We find the fault

    For the $69 diagnostic visit, credited to the repair if you go ahead.

  3. Get the price in writing

    Before any work starts. No repair until you say yes.

  4. We fix it

    Only the work you approved, at the price you approved.

  5. Get the paperwork

    The appliance, the work done and the date, in writing.

Whirlpool dishwasher questions

Not covered here? Call (813) 513-1699 Text a photo

Why is the Clean light blinking on my Whirlpool dishwasher?

Without a display, it’s an error code. Count the first run of quick flashes (the F number), then, after a short pause, the second run (the E number). Nine, then one, is F9 E1.

How do I reset a Whirlpool dishwasher?

Press Cancel and let it drain. Unplug it, or switch off its breaker if it’s wired in, for at least a minute. Shut the door firmly, pick a cycle, press Start. Code back? Text us a photo.

How often should a Whirlpool dishwasher filter be cleaned?

Every one to three months, says Whirlpool’s 2025 quick start guide. Pull out the lower rack, turn the filter cup a quarter turn counterclockwise, lift it out, then take out the filter plate; rinse both under cold water. Never run it with filters loose or missing.

How long is the warranty on a Whirlpool dishwasher?

One year from delivery, parts and labor: Whirlpool pays to correct defects in materials or workmanship, and asks for proof of purchase. During that year Whirlpool arranges the repair, so start with Whirlpool.

More on Whirlpool and dishwashers

Where we work

Beaver Appliance repairs Whirlpool dishwashers across South Florida: Broward County and nearby parts of Miami-Dade and Palm Beach counties. Call or text (754) 285-8880.

Beaver Appliance repairs Whirlpool dishwashers across Tampa Bay: Pasco and Hillsborough counties and nearby parts of Pinellas and Hernando counties. Call or text (813) 513-1699.