Beaver Appliance

GE washer repair, top-load and front-load.

GE Appliances A brand we repair

Beaver Appliance repairs GE top-load and front-load washers in South Florida and Tampa Bay, as an independent company not affiliated with GE Appliances. A $69 diagnostic visit finds the fault, credited to the repair; the price is in writing before any work.

Call or text and we’ll give you the earliest time we have.

Diagnostic visit
$69, credited to the repair
Price
In writing, before any work
Work done
Only what you approve
Google rating, South Florida
5.0 from 14 reviews
The control knobs of a white laundry center above the lid of its top-load washer
A white laundry center in a bright laundry room: a top-load washer below, a dryer above, controls between them

A washer fix and more, in customers’ words

Our South Florida Google profile: rated 5.0 from 14 Beaver Appliance reviews.

  • Washing machine

    “Aizat was very prompt and did a wonderful job fixing my washing machine. …”

    ★★★★★ Debbie B. Jul 2026, Google review
  • Appliance repair

    “… He diagnosed the problem quickly, explained what needed to be done, and got the job done right. …”

    ★★★★★ Arlene J. Aug 2026, Google review

What is your GE washer doing?

Showing a message? See the message table.

Won’t start or fill

First check: the breaker, its own outlet, both water valves fully open. GE says low pressure or clogged inlet screens can time some models out.

Call us if water still won’t come in.

Water left in the tub

First check: wait, since GE says pauses of up to three minutes are normal. Then a kinked drain hose, or a front-loader’s pump filter: unplug it, put a shallow pan and towels under it and open it slowly, as GE says, since the tub’s water drains out there. GE’s test: pour a quart of water into the standpipe; if it won’t drain, call a plumber.

Call us if the tub stays full and the washer just hums.

Clothes still soaking wet

First check: a top-loader won’t spin with the lid up, nor a front-loader with its drawer open or too small a load. Too much detergent can cause a suds lock, GE says: use HE.

Call us if the motor runs but the tub won’t spin.

Water on the floor

First check: standing in water? Switch it off at the breaker, never at the plug, GE says, and shut the valves behind it. Then a front-loader’s door seal wiped clean, pods in the drum, not the drawer. A top-loader leaking at the front left corner is usually oversudsing, GE says: less detergent. At the wall, a rubber washer in each hose end.

Call us if it overfills, or drips while it’s off.

Shakes, bangs or walks

First check: the shipping hardware out (a front-loader’s rear bolts, a top-loader’s rod, foam or cardboard cone) and all four legs firm on the floor. A front-loader moving a quarter inch is normal, GE says.

Call us if it shakes empty and level.

Door or lid stays locked

First check: Start/Pause unlocks a top-loader’s lid. A front-loader’s door can take 30 seconds; never force it. UltraFresh Vent keeps it locked up to 8 hours; Power cancels it. Still locked? GE says check the pump filter: unplugged, a pan and towels under it, opened slowly.

Call us if it stays locked with the filter clear.

GE washer display messages and lights

Photograph the display or the blinking lights first, then wait out GE’s lock-out.

After H2O SUPPLY, a blinking Fill light or a front-loader’s CAnCELEd, the controls stay locked 3 or 4 minutes; unplugging starts the timer over. GE Profile front-loaders share these messages.

On the display What GE says it means First check, then
H2O SUPPLY Fill light, 2 blinks

Water isn’t entering the washer

Both valves on; then wait out the lock-out.

Po Rinse light blinking

Top-load: it took too long to pump the water out; there may be a clog

Press Start, or Drain & Spin; then check for a pinched hose.

bALAnCINg Spin light blinking

The load is out of balance, so it can’t spin properly

Spread the load evenly, then Drain & Spin.

CAnCELEd Two outer lights blinking

Top-load: an error has occurred. Front-load: paused over 24 hours, or stopped by certain errors Differs by type

Top-load: Drain & Spin; if it persists, power off a minute. Front-load: wait out the lock-out.

door Lid light blinking

Three cycles started without opening the door or lid; on a front-loader, also a door not fully shut

Open and close it, then start a new cycle.

dE E2

Top-load: the lid was opened, so it paused; it shuts off after about 30 seconds

Close the lid, then press Start/Pause.

Fill light 3 blinks

Top-load: water sat 15 minutes with the lid open, so it drains Not a fault

Close the lid, then start a new cycle.

Venting Door icon, Control lock

Front-load: a step or a setting Not a fault

Venting blinking: UltraFresh Vent can be chosen. Door icon blinking: pausing to unlock. Lock icon: hold Control Lock 3 seconds.

Text us the message and the label

Top-loader: under the lid, near the right hinge. Front-loader: inside the door, on the wash compartment’s face. GE model numbers begin and end with a letter.

Text a photo to (813) 513-1699

What a GE washer visit involves

  1. Tell us what it’s doing

    Call or text us. The appliance, the symptom and any code are enough to start.

  2. We find the fault

    For the $69 diagnostic visit, credited to the repair if you go ahead.

  3. Get the price in writing

    Before any work starts. No repair until you say yes.

  4. We fix it

    Only the work you approved, at the price you approved.

  5. Get the paperwork

    The appliance, the work done and the date, in writing.

GE washer questions

Didn’t see yours? Call (813) 513-1699 Text a photo

Is there a GE washer error code list?

Not one GE publishes for owners. Its manuals explain messages and lights instead: GE’s Consumer Help Indicator. Numbered codes such as 38 aren’t on GE’s owner pages, so text us a photo of yours and the model label.

How do I reset a GE washer?

Unplug the washer, or switch off its breaker, for 2 minutes, GE says; then choose the cycle again and press Start. Not during a lock-out: unplugging restarts that timer. Message back? Text us a photo.

Is my GE washer still under warranty?

GE covers a washer for one year from purchase, parts and labor, for defects; keep proof of the date. Many GE front-loaders and some top-loaders cover the motor for ten years; after year one, the part only, not the labor. Past those terms, you choose the repairer.

Is my GE Profile washer part of a recall?

CPSC’s 2016 notice covers GE Profile top-loaders WPGT9350, WPGT9360 and WPGT9150, every serial number, sold June 2003 through October 2011: an electrical component can overheat, posing a fire hazard. CPSC says to unplug and stop using one immediately and contact GE Appliances.

More on GE and washers

Where we work

Beaver Appliance repairs GE washers across South Florida: Broward County and nearby parts of Miami-Dade and Palm Beach counties. Call or text (754) 285-8880.

Beaver Appliance repairs GE washers across Tampa Bay: Pasco and Hillsborough counties and nearby parts of Pinellas and Hernando counties. Call or text (813) 513-1699.